Appliance error codes and what to try first

An error code tells you which part of the appliance stopped a cycle. About a third of the codes we are called for clear with a ten-minute fix you can do yourself.

Start with a five-minute reset

Unplug the appliance for five minutes, then plug it back in. That clears a code caused by a power blip, and it costs nothing.

  1. Write the code down. And what the appliance was doing when it stopped: filling, draining, heating or spinning.
  2. Unplug it, or flip its breaker. Wait a full five minutes so the control board loses its memory.
  3. Run a short cycle. If the code comes back at the same point, it is a real fault. Look it up below.

Look up a code by appliance

Tap your appliance. Codes differ by brand and model, so treat these as the usual meaning and check the sticker inside the door.

Washer codes
Common washer codes
CodeUsually meansTry this first
E21 or F21Water is not drainingClean the drain filter behind the small door at the bottom front
dE or dLDoor lock problemClose the door firmly; check for clothes caught in the seal
UE or UbLoad is out of balanceSpread the load out, or add a towel to a single heavy item
4E or F8 E1Not filling with waterOpen both taps fully and check the fill hoses for kinks
Sud or SDToo many sudsRun a rinse with no soap; use less, and only HE soap
Dryer codes
Common dryer codes
CodeUsually meansTry this first
E3 or AFExhaust is blockedClean the lint trap and the vent hose behind the dryer
tE or F22Temperature sensor faultReset once. If it returns, the sensor needs replacing
dE or dODoor is not latchingClear lint from the latch and close it firmly
PFPower failed mid-cyclePress Start again; nothing is wrong with the dryer
Refrigerator codes
Common refrigerator codes
CodeUsually meansTry this first
OF or O FFDemo mode is onHold the two top buttons for 3 seconds
Er IF or 5EIce maker fan faultCheck for ice packed around the ice maker; thaw and reset
Er FF or 22EFreezer fan faultUnplug, thaw any ice on the back panel, restart
dHDefrost took too longReset once. If it returns, a defrost part has failed
Dishwasher codes
Common dishwasher codes
CodeUsually meansTry this first
LE or LCLeak sensor trippedTurn off power, tilt forward gently to drain the base
OE or 5CNot drainingClean the filter in the tub floor; check the sink disposal knockout plug
IE or 4CNot fillingOpen the supply valve under the sink fully
HEWater is not heatingReset once. If it returns, the heating element has likely failed
Range and oven codes
Common range and oven codes
CodeUsually meansTry this first
F1 or F10Control board or runaway temperatureFlip the breaker off for five minutes. If it returns, call
F3 or F4Oven temperature sensorCheck that the sensor rod at the back of the oven is not touching the wall
F5 or drDoor lock faultLet the oven cool fully after self-clean, then reset
LOCControl lock is onHold the Lock button for 3 seconds

Where is my model number?

It is on a sticker inside the door or lid, not on the front. Have it ready when you call and we can load the right part on the van.

When should I stop and call?

Stop and call if you smell gas or burning, see water on the floor, or the same code comes back after a reset.

If you smell gas, do this first

Leave the house, then call your gas company from outside. Do not unplug anything or flip a switch. Call us after they say it is safe, and we will find the leak in the appliance.

Code came back?

Tell us the code and the model number when you book. Common parts ride on the van, so most code repairs are done on the first visit.

Book a tech Call (555) 555-5555