Lighting, fans and outbuildings.

Good light changes a room more than paint does. We put in recessed lights, fans, under-cabinet strips and yard lighting, and wire shops and barns from the ground up.

Lighting and fan prices

Labor and wiring. You supply the fixture, or we do. Sample prices for this concept site.

Common lighting jobs
JobPrice
Swap a light fixture, same spot$95
Hang a ceiling fan where a light was, with a fan-rated box$185
New recessed light, each, four or more$145
Add a dimmer$85
Under-cabinet lighting, a typical kitchen$480
New light and switch where there was none$260 to $340
Chandelier over 50 pounds, or above a stairwell$240 to $420

Recessed lights, done well

  • Spacing: about half the ceiling height apart. Eight-foot ceilings want lights every four feet.
  • Off the walls: thirty inches out, so the light washes down the wall and not onto the top of your head.
  • Warm, not blue: 2700K in living rooms and bedrooms, 3000K in kitchens and baths.
  • On a dimmer, always. Full brightness is for cleaning.
  • Thin LED fixtures fit under joists and ducts where old cans could not go.
  • We cut clean holes with a dust shroud and patch nothing, since nothing breaks.
Electrician in a white hard hat and gloves fitting a long light fixture to a wall

Ceiling fans

Three things decide whether a fan is a pleasure or a wobble.

  1. A fan-rated box

    An ordinary light box will not hold a fan for long. We fit a braced one between the joists.

  2. The correct size

    42 inches for a small bedroom, 52 for most rooms, 60 or more for a great room.

  3. A wall control

    A switch for the light and one for the fan beats a pull chain. Often the wire is already there.

Outdoors

  • Porch and garage lights on a photocell, so they come on at dusk without a timer.
  • Motion lights at the back door and the drive.
  • Low-voltage path lights, with a transformer and buried cable. A typical front walk is $900 to $1,400.
  • Hot tub and pool wiring, with the disconnect, bonding and GFCI the code requires.
  • Outlets for holiday lights under the eaves, on one switch indoors.

Shops, barns and garages

Wiring an outbuilding. Sample prices for this concept site.
JobWhat is in itPrice
Detached garage, basicA buried feed, 60 amp subpanel, six outlets and four lights$2,800 to $3,600
Workshop100 amp subpanel, 240 volt outlets for a welder and a compressor, bright LED lighting$4,200 to $5,800
Pole barnService, lights, outlets at every other post and a frost-free hydrant circuit$3,500 to $6,000
TrenchingEighteen to twenty-four inches deep, by the foot$9 a foot

Tell us what machines will run. A welder and a compressor starting together need more than their labels suggest.

Row of pliers, cutters and screwdrivers with colored handles hanging on a workshop wall

Who does the work

  • Rick Dawes, master electrician, 22 years in the trade.
  • Tony, his journeyman, who has been with him for nine of them.
  • Both wear shoe covers, lay drop cloths and vacuum before they leave.
  • Every job is permitted when the city requires it, and inspected.
  • Two years on our labor, and the maker's warranty on every fixture.

Planning a lighting job

Asked about lighting

Can you add lights without tearing up the ceiling?

Nearly always. We fish the wire through from the attic or from one fixture to the next.

Why do my LED bulbs flicker on the dimmer?

The dimmer is an old kind made for incandescent bulbs. A new LED dimmer, $85 installed, cures it.

Will you hang a fixture I bought online?

Yes. If it arrives damaged or missing parts, we tell you before it goes up.

Do I need a permit to wire my shop?

Inside city limits, yes. In the county, the rules vary. We find out and handle it either way.

Tell us about the room.

A few photos and the ceiling height are enough for a price on most lighting jobs.